View NCP304LSQ46T1G_5005071.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? semiconductor components industries, llc, 2007 september, 2007 - rev. 19 1 publication order number: ncp304/d ncp304, ncp305 voltage detector series the ncp304 and ncp305 series are second generation ultra-low current voltage detectors. these devices are specifically designed for use as reset controllers in portable microprocessor based systems where extended battery life is paramount. each series features a highly accurate undervoltage detector with hysteresis which prevents erratic system reset operation as the comparator threshold is crossed. the ncp304 series consists of complementary output devices that are available with either an active high or active low reset output. the ncp305 series has an open drain n-channel output with an active low reset output. the ncp304 and ncp305 device series are available in the sc-82ab package with standard undervoltage thresholds. additional thresholds that range from 0.9 v to 4.9 v in 100 mv steps can be manufactured. features ? quiescent current of 1.0 a typical ? high accuracy undervoltage threshold of 2.0% ? wide operating voltage range of 0.8 v to 10 v ? complementary or open drain reset output ? active low or active high reset output ? pb-free packages are available typical applications ? microprocessor reset controller ? low battery detection ? power fail indicator ? battery backup detection ncp305lsqxxt1 open drain output configuration ncp304xsqxxt1 complementary output configuration v ref v ref input reset output gnd 4 1 2 input reset output gnd 4 1 2 * * the representative block diagram depicts active low reset output `l' suffix devices. the comparator input is interchanged for the active high output `h' suffix devices. this device contains 38 active transistors. this device contains 37 active transistors. figure 1. representative block diagrams see detailed ordering and shipping information in the ordering information section on page 19 of this data sheet. ordering information sc-82ab sq suffix case 419c pin connections and marking diagram 4 1 reset output n.c. (top view) xxx = specific device code m = date code = pb-free package http://onsemi.com 1 2 43 gnd v in xxx m (note: microdot may be in either location)
ncp304, ncp305 http://onsemi.com 2 maximum ratings (note 1) rating symbol value unit input power supply voltage (pin 2) v in 12 v output voltage (pin 1) complementary, ncp304 n-channel open drain, ncp305 v out -0.3 to v in +0.3 -0.3 to 12 v output current (pin 1) (note 2) i out 70 ma thermal resistance, junction-to-air r ja 285 c/w maximum junction temperature t j +125 c storage temperature range t stg -55 to +150 c latchup performance (note 3) positive negative i latchup 500 170 ma stresses exceeding maximum ratings may damage the device. maximum ratings are stress ratings only. functional operation above t he recommended operating conditions is not implied. extended exposure to stresses above the recommended operating conditions may af fect device reliability. 1. this device series contains esd protection and exceeds the following tests: human body model 2000 v per mil-std-883, method 3015. machine model method 200 v. 2. the maximum package power dissipation limit must not be exceeded. p d t j(max) -t a r ja 3. maximum ratings per jedec standard jesd78. electrical characteristics (for all values t a = 25 c, unless otherwise noted.) characteristic symbol min typ max unit ncp304/5 - 0.9 detector threshold (pin 2, v in decreasing) v det- 0.882 0.900 0.918 v detector threshold hysteresis (pin 2, v in increasing) v hys 0.027 0.045 0.063 v supply current (pin 2) (v in = 0.8 v) (v in = 2.9 v) i in - - 0.8 - 2.4 3.0 a maximum operating voltage (pin 2) v in(max) - - 10 v minimum operating voltage (pin 2) (t a = -40 c to 85 c) v in(min) - - 0.55 0.65 0.70 0.80 v reset output current (pin 1, active low `l' suffix devices) i out ma n-channel sink current, ncp304, ncp305 (v out = 0.05 v, v in = 0.70 v) (v out = 0.50 v, v in = 0.85 v) 0.01 0.05 0.05 0.50 - - p-channel source current, ncp304 (v out = 2.4 v, v in = 4.5 v) 1.0 2.0 - reset output current (pin 1, active high `h' suffix devices) i out ma n-channel sink current, ncp304, ncp305 (v out = 0.5 v, v in = 1.5 v) 1.05 2.5 - p-channel source current, ncp304 (v out = 0.4 v, v in = 0.7 v) (v out = gnd, v in = 0.8 v) 0.011 0.014 0.04 0.08 - - propagation delay input to output (figure 2) s 4. in the case of cmos output type: the time interval between the rising edge of v dd input pulse from 0.7 v to (+v det ) +2.0 v and output voltage level becoming to v dd /2. in the case of n-channel open drain output type: output pin is pulled up with a resistance of 470 k to 5.0 v, the time interval between the rising edge of v dd input pulse from 0.7 v to (+v det ) +2.0 v and output voltage level becoming to 2.5 v.
ncp304, ncp305 http://onsemi.com 3 electrical characteristics (continued) (for all values t a = 25 c, unless otherwise noted.) characteristic unit max typ min symbol ncp304/5 - 0.9 complementary output ncp304 series output transition, high to low (note 4) output transition, low to high (note 4) t phl t plh - - 18 6.0 - 60 n-channel open drain ncp305 series output transition, high to low (note 4) output transition, low to high (note 4) t phl t plh - - 18 - - 100 ncp304/5 - 1.8 detector threshold (pin 2, v in decreasing) v det- 1.764 1.80 1.836 v detector threshold hysteresis (pin 2, v in increasing) v hys 0.054 0.090 0.126 v supply current (pin 2) (v in = 1.7 v) (v in = 3.8 v) i in - - 0.8 1.0 2.4 3.0 a maximum operating voltage (pin 2) v in(max) - - 10 v minimum operating voltage (pin 2) (t a = -40 c to 85 c) v in(min) - - 0.55 0.65 0.70 0.80 v reset output current (pin 1, active low `l' suffix devices) i out ma n-channel sink current, ncp304, ncp305 (v out = 0.05 v, v in = 0.70 v) (v out = 0.50 v, v in = 1.5 v) 0.01 1.0 0.05 2.0 - - p-channel source current, ncp304 (v out = 2.4 v, v in = 4.5 v) 1.0 2.0 - reset output current (pin 1, active high `h' suffix devices) i out ma n-channel sink current, ncp304, ncp305 (v out = 0.5 v, v in = 5.0 v) 6.3 11 - p-channel source current, ncp304 (v out = 0.4 v, v in = 0.7 v) (v out = gnd, v in = 1.5 v) 0.011 0.525 0.04 0.6 - - propagation delay input to output (figure 2) s complementary output ncp304 series output transition, high to low (note 4) output transition, low to high (note 4) t phl t plh - - 14 15 - 60 n-channel open drain ncp305 series output transition, high to low (note 4) output transition, low to high (note 4) t phl t plh - - 14 - - 100 ncp304/5 - 2.0 detector threshold (pin 2, v in decreasing) v det- 1.960 2.00 2.040 v detector threshold hysteresis (pin 2, v in increasing) v hys 0.06 0.10 0.14 v supply current (pin 2) (v in = 1.9 v) (v in = 4.0 v) i in - - 0.9 1.1 2.7 3.3 a maximum operating voltage (pin 2) v in(max) - - 10 v minimum operating voltage (pin 2) (t a = -40 c to 85 c) v in(min) - - 0.55 0.65 0.70 0.80 v reset output current (pin 1, active low `l' suffix devices) i out ma 4. in the case of cmos output type: the time interval between the rising edge of v dd input pulse from 0.7 v to (+v det ) +2.0 v and output voltage level becoming to v dd /2. in the case of n-channel open drain output type: output pin is pulled up with a resistance of 470 k to 5.0 v, the time interval between the rising edge of v dd input pulse from 0.7 v to (+v det ) +2.0 v and output voltage level becoming to 2.5 v.
ncp304, ncp305 http://onsemi.com 4 electrical characteristics (continued) (for all values t a = 25 c, unless otherwise noted.) characteristic unit max typ min symbol ncp304/5 - 2.0 n-channel sink current, ncp304, ncp305 (v out = 0.05 v, v in = 0.70 v) (v out = 0.50 v, v in = 1.5 v) 0.01 1.0 0.05 2.0 - - p-channel source current, ncp304 (v out = 2.4 v, v in = 4.5 v) 1.0 2.0 - reset output current (pin 1, active high `h' suffix devices) i out ma n-channel sink current, ncp304, ncp305 (v out = 0.5 v, v in = 5.0 v) 6.3 11 - p-channel source current, ncp304 (v out = 0.4 v, v in = 0.7 v) (v out = gnd, v in = 1.5 v) 0.011 0.525 0.04 0.6 - - propagation delay input to output (figure 2) s complementary output ncp304 series output transition, high to low (note 4) output transition, low to high (note 4) t phl t plh - - 13 15 - 60 n-channel open drain ncp305 series output transition, high to low (note 4) output transition, low to high (note 4) t phl t plh - - 13 - - 100 ncp304/5 - 2.7 detector threshold (pin 2, v in decreasing) v det- 2.646 2.700 2.754 v detector threshold hysteresis (pin 2, v in increasing) v hys 0.081 0.135 0.189 v supply current (pin 2) (v in = 2.6 v) (v in = 4.7 v) i in - - 0.9 1.1 2.7 3.3 a maximum operating voltage (pin 2) v in(max) - - 10 v minimum operating voltage (pin 2) (t a = -40 c to 85 c) v in(min) - - 0.55 0.65 0.70 0.80 v reset output current (pin 1, active low `l' suffix devices) i out ma n-channel sink current, ncp304, ncp305 (v out = 0.05 v, v in = 0.70 v) (v out = 0.50 v, v in = 1.5 v) 0.01 1.0 0.05 2.0 - - p-channel source current, ncp304 (v out = 2.4 v, v in = 4.5 v) 1.0 2.0 - reset output current (pin 1, active high `h' suffix devices) i out ma n-channel sink current, ncp304, ncp305 (v out = 0.5 v, v in = 5.0 v) 6.3 11 - p-channel source current, ncp304 (v out = 0.4 v, v in = 0.7 v) (v out = gnd, v in = 1.5 v) 0.011 0.525 0.04 0.6 - - propagation delay input to output (figure 2) s complementary output ncp304 series output transition, high to low (note 4) output transition, low to high (note 4) t phl t plh - - 12 19 - 60 n-channel open drain ncp305 series output transition, high to low (note 4) output transition, low to high (note 4) t phl t plh - - 12 - - 100 4. in the case of cmos output type: the time interval between the rising edge of v dd input pulse from 0.7 v to (+v det ) +2.0 v and output voltage level becoming to v dd /2. in the case of n-channel open drain output type: output pin is pulled up with a resistance of 470 k to 5.0 v, the time interval between the rising edge of v dd input pulse from 0.7 v to (+v det ) +2.0 v and output voltage level becoming to 2.5 v.
ncp304, ncp305 http://onsemi.com 5 electrical characteristics (continued) (for all values t a = 25 c, unless otherwise noted.) characteristic unit max typ min symbol ncp304/5 - 2.9 detector threshold (pin 2, v in decreasing) v det- 2.842 2.900 2.958 v detector threshold hysteresis (pin 2, v in increasing) v hys 0.087 0.145 0.203 v supply current (pin 2) (v in = 2.8 v) (v in = 4.9 v) i in - - 0.9 1.1 2.9 3.5 a maximum operating voltage (pin 2) v in(max) - - 10 v minimum operating voltage (pin 2) (t a = -40 c to 85 c) v in(min) - - 0.55 0.65 0.70 0.80 v reset output current (pin 1, active low `l' suffix devices) i out ma n-channel sink current, ncp304, ncp305 (v out = 0.05 v, v in = 0.70 v) (v out = 0.50 v, v in = 1.5 v) 0.01 1.0 0.05 2.0 - - p-channel source current, ncp304 (v out = 2.4 v, v in = 4.5 v) 1.0 2.0 - reset output current (pin 1, active high `h' suffix devices) i out ma n-channel sink current, ncp304, ncp305 (v out = 0.5 v, v in = 5.0 v) 6.3 11 - p-channel source current, ncp304 (v out = 0.4 v, v in = 0.7 v) (v out = gnd, v in = 1.5 v) 0.011 0.525 0.04 0.6 - - propagation delay input to output (figure 2) s complementary output ncp304 series output transition, high to low (note 4) output transition, low to high (note 4) t phl t plh - - 12 19 - 60 n-channel open drain ncp305 series output transition, high to low (note 4) output transition, low to high (note 4) t phl t plh - - 12 - - 100 ncp304/5 - 3.0 detector threshold (pin 2, v in decreasing) v det- 2.94 3.00 3.06 v detector threshold hysteresis (pin 2, v in increasing) v hys 0.09 0.15 0.21 v supply current (pin 2) (v in = 2.87 v) (v in = 5.0 v) i in - - 1.0 1.2 3.0 3.6 a maximum operating voltage (pin 2) v in(max) - - 10 v minimum operating voltage (pin 2) (t a = -40 c to 85 c) v in(min) - - 0.55 0.65 0.70 0.80 v reset output current (pin 1, active low `l' suffix devices) i out ma n-channel sink current, ncp304, ncp305 (v out = 0.05 v, v in = 0.70 v) (v out = 0.50 v, v in = 1.5 v) 0.01 1.0 0.05 2.0 - - p-channel source current, ncp304 (v out = 2.4 v, v in = 4.5 v) 1.0 2.0 - reset output current (pin 1, active high `h' suffix devices) i out ma n-channel sink current, ncp304, ncp305 (v out = 0.5 v, v in = 5.0 v) 6.3 11 - 4. in the case of cmos output type: the time interval between the rising edge of v dd input pulse from 0.7 v to (+v det ) +2.0 v and output voltage level becoming to v dd /2. in the case of n-channel open drain output type: output pin is pulled up with a resistance of 470 k to 5.0 v, the time interval between the rising edge of v dd input pulse from 0.7 v to (+v det ) +2.0 v and output voltage level becoming to 2.5 v.
ncp304, ncp305 http://onsemi.com 6 electrical characteristics (continued) (for all values t a = 25 c, unless otherwise noted.) characteristic unit max typ min symbol ncp304/5 - 3.0 p-channel source current, ncp304 (v out = 0.4 v, v in = 0.7 v) (v out = gnd, v in = 1.5 v) 0.011 0.525 0.04 0.6 - - propagation delay input to output (figure 2) s complementary output ncp304 series output transition, high to low (note 4) output transition, low to high (note 4) t phl t plh - - 12 19 - 60 n-channel open drain ncp305 series output transition, high to low (note 4) output transition, low to high (note 4) t phl t plh - - 12 - - 100 ncp304/5 - 4.5 detector threshold (pin 2, v in decreasing) v det- 4.410 4.500 4.590 v detector threshold hysteresis (pin 2, v in increasing) v hys 0.135 0.225 0.315 v supply current (pin 2) (v in = 4.34 v) (v in = 6.5 v) i in - - - - 3.0 3.9 a maximum operating voltage (pin 2) v in(max) - - 10 v minimum operating voltage (pin 2) (t a = -40 c to 85 c) v in(min) - - 0.55 0.65 0.70 0.80 v reset output current (pin 1, active low `l' suffix devices) i out ma n-channel sink current, ncp304, ncp305 (v out = 0.05 v, v in = 0.70 v) (v out = 0.50 v, v in = 1.5 v) 0.01 1.0 0.05 2.0 - - p-channel source current, ncp304 (v out = 5.9 v, v in = 8.0 v) 1.5 3.0 - reset output current (pin 1, active high `h' suffix devices) i out ma n-channel sink current, ncp304, ncp305 (v out = 0.5 v, v in = 5.0 v) 6.3 11 - p-channel source current, ncp304 (v out = 0.4 v, v in = 0.7 v) (v out = gnd, v in = 1.5 v) 0.011 0.525 0.04 0.6 - - propagation delay input to output (figure 2) s complementary output ncp304 series output transition, high to low (note 4) output transition, low to high (note 4) t phl t plh - - 10 21 - 60 n-channel open drain ncp305 series output transition, high to low (note 4) output transition, low to high (note 4) t phl t plh - - 10 - - 100 ncp304/5 - 4.7 detector threshold (pin 2, v in decreasing) v det- 4.606 4.70 4.794 v detector threshold hysteresis (pin 2, v in increasing) v hys 0.141 0.235 0.329 v supply current (pin 2) (v in = 4.54 v) (v in = 6.7 v) i in - - 1.1 1.3 3.0 3.9 a maximum operating voltage (pin 2) v in(max) - - 10 v 4. in the case of cmos output type: the time interval between the rising edge of v dd input pulse from 0.7 v to (+v det ) +2.0 v and output voltage level becoming to v dd /2. in the case of n-channel open drain output type: output pin is pulled up with a resistance of 470 k to 5.0 v, the time interval between the rising edge of v dd input pulse from 0.7 v to (+v det ) +2.0 v and output voltage level becoming to 2.5 v.
ncp304, ncp305 http://onsemi.com 7 electrical characteristics (continued) (for all values t a = 25 c, unless otherwise noted.) characteristic unit max typ min symbol ncp304/5 - 4.7 minimum operating voltage (pin 2) (t a = -40 c to 85 c) v in(min) - - 0.55 0.65 0.70 0.80 v reset output current (pin 1, active low `l' suffix devices) i out ma n-channel sink current, ncp304, ncp305 (v out = 0.05 v, v in = 0.70 v) (v out = 0.50 v, v in = 1.5 v) 0.01 1.0 0.05 2.0 - - p-channel source current, ncp304 (v out = 5.9 v, v in = 8.0 v) 1.5 3.0 - reset output current (pin 1, active high `h' suffix devices) i out ma n-channel sink current, ncp304, ncp305 (v out = 0.5 v, v in = 5.0 v) 6.3 11 - p-channel source current, ncp304 (v out = 0.4 v, v in = 0.7 v) (v out = gnd, v in = 1.5 v) 0.011 0.525 0.04 0.6 - - propagation delay input to output (figure 2) s complementary output ncp304 series output transition, high to low (note 4) output transition, low to high (note 4) t phl t plh - - 10 21 - 60 n-channel open drain ncp305 series output transition, high to low (note 4) output transition, low to high (note 4) t phl t plh - - 10 - - 100 4. in the case of cmos output type: the time interval between the rising edge of v dd input pulse from 0.7 v to (+v det ) +2.0 v and output voltage level becoming to v dd /2. in the case of n-channel open drain output type: output pin is pulled up with a resistance of 470 k to 5.0 v, the time interval between the rising edge of v dd input pulse from 0.7 v to (+v det ) +2.0 v and output voltage level becoming to 2.5 v.
ncp304, ncp305 http://onsemi.com 8 figure 2. propagation delay measurement conditions ncp304 and ncp305 series are measured with a 10 pf capacitive load. ncp305 has an additional 470 k pullup resistor connected from the reset output to +5.0 v. the reset output voltage waveforms are shown for the active low `l ' devices. the upper detecto r threshold, v det+ is the sum of the lower detector threshold, v det- plus the input hysteresis, v hys . input voltage, pin 2 reset output voltage, pin 1 0.7 0 v 5 v 0 v 0.5 v 2.5 v ncp304l complementary ncp305l open drain t plh t phl 0.1 v reset output voltage, pin 1 0 v v det+ + 2 v det+ + 2 v det+ + 2 2
ncp304, ncp305 http://onsemi.com 9 table 1. ncp304 series electrical characteristic table for 0.9 - 4.9 v part number detector threshold detector threshold hysteresis supply current n-channel sink cur\ rent p-channel source current v in low v in high v in low v in high v det- (v) v hys (v) i in ( a) (note 5) i in ( a) (note 6) i out (ma) (note 7) i out (ma) (note 8) i out (ma) (note 9) min typ max min typ max typ typ typ typ typ ncp304lsq09t1 0.882 0.9 0.918 0.027 0.045 0.063 0.8 0.9 0.05 0.5 2.0 ncp304lsq15t1 1.470 1.5 1.530 0.045 0.075 0.105 ncp304lsq18t1 1.764 1.8 1.836 0.054 0.090 0.126 ncp304lsq20t1 1.960 2.0 2.040 0.060 0.100 0.140 0.9 1.1 ncp304lsq23t1 2.254 2.3 2.346 0.069 0.115 0.161 ncp304lsq25t1 2.450 2.5 2.550 0.075 0.125 0.175 ncp304lsq27t1 2.646 2.7 2.754 0.081 0.135 0.189 ncp304lsq29t1 2.842 2.9 2.958 0.087 0.145 0.203 ncp304lsq30t1 2.940 3.0 3.060 0.090 0.150 0.210 1.0 1.2 ncp304lsq33t1 3.234 3.3 3.366 0.099 0.165 0.231 ncp304lsq37t1 3.626 3.7 3.774 0.111 0.185 0.259 ncp304lsq38t1 3.724 3.8 3.876 0.114 0.190 0.266 ncp304lsq40t1 3.920 4.0 4.080 0.120 0.200 0.280 1.1 1.3 3.0 ncp304lsq42t1 4.116 4.2 4.284 0.126 0.210 0.294 ncp304lsq43t1 4.214 4.3 4.386 0.129 0.215 0.301 ncp304lsq45t1 4.410 4.5 4.590 0.135 0.225 0.315 ncp304lsq46t1 4.508 4.6 4.692 0.138 0.230 0.322 ncp304lsq47t1 4.606 4.7 4.794 0.141 0.235 0.329 5. condition 1: 0.9 - 2.9 v, v in = v det- - 0.10 v; 3.0 - 3.9 v, v in = v det- - 0.13 v; 4.0 - 4.9 v, v in = v det- - 0.16 v 6. condition 2: 0.9 - 4.9 v, v in = v det- + 2.0 v 7. condition 3: 0.9 - 4.9 v, v in = 0.7 v, v out = 0.05 v, active low `l' suffix devices 8. condition 4: 0.9 - 1.0 v, v in = 0.85 v, v out = 0.5 v; 1.1 - 1.5 v, v in = 1.0 v, v out = 0.5 v; 1.6 - 4.9 v, v in = 1.5 v, v out = 0.5 v, condition 4: active low `l' suffix devices 9. condition 5: 0.9 - 3.9 v, v in = 4.5 v, v out = 2.4 v; 4.0 - 4.9 v, v in = 8.0 v, v out = 5.9 v, active low `l' suffix devices table 2. ncp304 series electrical characteristic table for 0.9 - 4.9 v part number detector threshold detector threshold hysteresis supply current n-channel sink current p-channel source current v in low v in high v in low v in high v det- (v) v hys (v) i in ( a) (note 10) i in ( a) (note 11) i out (ma) (note 12) i out (ma) (note 13) i out (ma) (note 14) min typ max min typ max typ typ typ typ typ ncp304hsq09t1 0.882 0.9 0.918 0.027 0.045 0.063 0.8 0.9 2.5 0.04 0.08 ncp304hsq18t1 1.764 1.8 1.836 0.054 0.090 0.126 ncp304hsq20t1 1.960 2.0 2.040 0.060 0.100 0.140 0.9 1.1 ncp304hsq22t1 2.156 2.2 2.244 0.066 0.110 0.154 ncp304hsq27t1 2.646 2.7 2.754 0.081 0.135 0.189 ncp304hsq29t1 2.842 2.9 2.958 0.087 0.145 0.203 ncp304hsq30t1 2.940 3.0 3.060 0.090 0.150 0.210 1.0 1.2 ncp304hsq45t1 4.410 4.5 4.590 0.135 0.225 0.315 ncp304hsq47t1 4.606 4.7 4.794 0.141 0.235 0.329 10. condition 1: 0.9 - 2.9 v, v in = v det- - 0.10 v; 3.0 - 3.9 v, v in = v det- - 0.13 v; 4.0 - 4.9 v, v in = v det- - 0.16 v 11. condition 2: 0.9 - 4.9 v, v in = v det- + 2.0 v 12. condition 3: 0.9 - 1.4 v, v in = 1.5 v, v out = 0.5 v; 1.5 - 4.9 v, v in = 5.0 v, v out = 0.5 v, active high `h' suffix devices 13. condition 4: 0.9 - 4.9 v, v in = 0.7 v, v out = 0.4 v, active high `h' suffix devices 14. condition 5: 0.9 - 1.0 v, v in = 0.8 v, v out = gnd; 1.1 - 1.5 v, v in = 1.0 v, v out = gnd; 1.6 - 4.9 v, v in = 1.5 v, v out = gnd, active high `h' suffix devices
ncp304, ncp305 http://onsemi.com 10 table 3. ncp305 series electrical characteristic table for 0.9 - 4.9 v part number detector threshold detector threshold hysteresis supply current n-channel sink current v in low v in high v in low v in high v det- (v) v hys (v) i in ( a) (note 15) i in ( a) (note 16) i out (ma) (note 17) i out (ma) (note 18) min typ max min typ max typ typ typ typ ncp305lsq09t1 0.882 0.9 0.918 0.027 0.045 0.063 0.8 0.9 0.05 0.5 ncp305lsq15t1 1.470 1.5 1.530 0.045 0.075 0.105 ncp305lsq16t1 1.568 1.6 1.632 0.048 0.080 0.112 2.0 ncp305lsq17t1 1.666 1.7 1.734 0.051 0.085 0.119 ncp305lsq18t1 1.764 1.8 1.836 0.054 0.090 0.126 ncp305lsq20t1 1.960 2.0 2.040 0.060 0.100 0.140 0.9 1.1 ncp305lsq22t1 2.156 2.2 2.244 0.066 0.110 0.154 ncp305lsq23t1 2.254 2.3 2.346 0.069 0.115 0.161 ncp305lsq24t1 2.352 2.4 2.448 0.072 0.120 0.168 ncp305lsq25t1 2.450 2.5 2.550 0.075 0.125 0.175 ncp305lsq26t1 2.548 2.6 2.652 0.078 0.130 0.182 ncp305lsq27t1 2.646 2.7 2.754 0.081 0.135 0.189 ncp305lsq28t1 2.744 2.8 2.856 0.084 0.140 0.196 ncp305lsq29t1 2.842 2.9 2.958 0.087 0.145 0.203 ncp305lsq30t1 2.940 3.0 3.060 0.090 0.150 0.210 1.0 1.2 ncp305lsq31t1 3.038 3.1 3.162 0.093 0.155 0.217 ncp305lsq32t1 3.136 3.2 3.264 0.096 0.160 0.224 ncp305lsq33t1 3.234 3.3 3.366 0.099 0.165 0.231 ncp305lsq34t1 3.332 3.4 3.468 0.102 0.170 0.238 ncp305lsq35t1 3.430 3.5 3.570 0.105 0.175 0.245 ncp305lsq36t1 3.528 3.6 3.672 0.108 0.180 0.252 ncp305lsq37t1 3.626 3.7 3.774 0.111 0.185 0.259 ncp305lsq40t1 3.920 4.0 4.080 0.120 0.200 0.280 1.1 1.3 ncp305lsq44t1 4.312 4.4 4.488 0.132 0.220 0.308 ncp305lsq45t1 4.410 4.5 4.590 0.135 0.225 0.315 ncp305lsq47t1 4.606 4.7 4.794 0.141 0.235 0.329 ncp305lsq49t1 4.802 4.9 4.998 0.147 0.245 0.343 15. condition 1: 0.9 - 2.9 v, v in = v det- - 0.10 v; 3.0 - 3.9 v, v in = v det- - 0.13 v; 4.0 - 4.9 v, v in = v det- - 0.16 v 16. condition 2: 0.9 - 4.9 v, v in = v det- + 2.0 v 17. condition 3: 0.9 - 4.9 v, v in = 0.7 v, v out = 0.05 v, active low `l' suffix devices 18. condition 4: 0.9 - 1.0 v, v in = 0.85 v, v out = 0.5 v; 1.1 - 1.5 v, v in = 1.0 v, v out = 0.5 v; 1.6 - 4.9 v, v in = 1.5 v, v out = 0.5 v, active low `l' suffix devices
ncp304, ncp305 http://onsemi.com 11 v out , output voltage (v) -50 4.9 t a , ambient temperature ( c) 4.8 4.7 4.6 4.4 -25 0 25 50 75 100 4.5 4.3 3.00 -50 0.98 t a , ambient temperature ( c) 2.90 0.96 2.80 0.94 2.70 0.92 2.60 0.88 -25 0 25 50 75 100 0.90 0.86 -50 -25 0 25 50 75 100 t a , ambient temperature ( c) 2.65 2.75 2.85 2.95 v det+ figure 3. ncp304/5 series 0.9 v detector threshold voltage vs. temperature figure 4. ncp304/5 series 2.7 v detector threshold voltage vs. temperature figure 5. ncp304/5 series 4.5 v detector threshold voltage vs. temperature v in , input voltage (v) 0 0.2 0.4 0.6 0.8 1.0 0.8 0.6 0.4 0.2 0 1.0 figure 6. ncp304l/5l series 0.9 v reset output voltage vs. input voltage 0 1.0 1.5 2.0 2.5 3.0 2.0 1.5 1.0 0.5 0 3.0 v in , input voltage (v) 0.5 2.5 figure 7. ncp304l/5l series 2.7 v reset output voltage vs. input voltage 0 1.0 2.0 3.0 4.0 5.0 4.0 3.0 2.0 1.0 0 5.0 6.0 7.0 6.0 v in , input voltage (v) figure 8. ncp304l/5l series 4.5 v reset output voltage vs. input voltage v out , output output (v) v out , output output (v) v det , detector threshold voltage (v) v det , detector threshold voltage (v) v det , detector threshold voltage (v) v det- v det+ v det- v det+ v det- t a = -30 c t a = 25 c t a = 85 c t a = -30 c t a = 25 c t a = 85 c t a = -30 c t a = 25 c t a = 85 c
ncp304, ncp305 http://onsemi.com 12 0 v out , output voltage (v) 0.2 0.4 0.6 0.8 1.0 1.2 0.6 0.4 0 0.2 0.8 1.0 0 35 25 15 5.0 0.5 1.0 1.5 2.0 2.5 3.0 10 0 3.5 4.0 20 30 v out , output voltage (v) t a = 25 c t a = 25 c v in , input voltage (v) 0 2.0 4.0 6.0 8.0 2.0 1.5 1.0 0.5 0 10 16 12 8.0 4.0 0 2.0 6.0 10 14 0 0.5 1.0 1.5 2.0 2.5 v out , output voltage (v) t a = 25 c v in = 2.0v v in = 1.5 v v in = 2.5 v v in = 4.0 v v in = 3.5 v v in = 3.0 v v in = 2.5 v v in = 2.0 v v in = 1.5 v t a = 25 c i out , output sink current (ma) i out , output sink current (ma) i out , output sink current (ma) i in , input current ( a) 1.5 v out , output voltage (v) i out , output source current (ma) 0 2.0 2.5 1.5 1.0 0.5 0.5 1.0 0 2.0 2.5 v in = 2.5 v v in = 2.0 v v in = 1.5 v 0 3.0 2.5 2.0 1.5 2.0 1.5 1.0 1.0 0.5 0 0.5 2.5 3.0 v in , input voltage (v) v out , output voltage (v) t a = -30 c t a = 25 c t a = 85 c figure 9. ncp304h/5h series 2.7 v reset output voltage vs. input voltage figure 10. ncp304h/5l series 0.9 v reset output sink current vs. output voltage figure 11. ncp304h/5l series 2.7 v reset output sink current vs. output voltage figure 12. ncp304h/5l series 4.5 v reset output sink current vs. output voltage figure 13. ncp304h series 2.7 v reset output source current vs. output voltage figure 14. ncp304/5 series 0.9 v input current vs. input voltage v in = 0.7 v v in = 0.85 v
ncp304, ncp305 http://onsemi.com 13 60 20 80 10 40 0 90 v in , input voltage (v) i out , output sink current (ma) 0 8.0 6.0 4.0 2.0 10 v out = v in - 2.1 v 70 50 30 = v in - 1.5 v = v in - 1.0 v = v in - 0.5 v v in , input voltage (v) 1.2 0.8 0.4 0 0.2 0.6 1.0 1.4 0 0.2 0.4 0.6 0.8 1.0 v in , input voltage (v) 0 7.0 5.0 3.0 1.0 0.5 1.0 1.5 2.0 2.5 3.0 2.0 0 4.0 6.0 v in , input voltage (v) 0 1.0 2.0 3.0 4.0 5.0 12 6.0 4.0 0 2.0 8.0 10 i out , output sink current (ma) i out , output sink current (ma) i out , output sink current (ma) t a = 85 c t a = 25 c t a = -30 c t a = -30 c t a = 85 c t a = 25 c t a = 25 c t a = -30 c t a = 85 c 2.0 0 2.0 6.0 8.0 10 0.5 0 v in , input voltage (v) 4.0 1.0 0 2.0 6.0 8.0 1.5 1.0 0.5 0 v in , input voltage (v) 4.0 10 1.5 2 i in , input current ( a) i in , input current ( a) figure 15. ncp304/5 series 2.7 v input current vs. input voltage figure 16. ncp304/5 series 4.5 v input current vs. input voltage figure 17. ncp304h/5l series 0.9 v reset output sink current vs. input voltage figure 18. ncp304h/5l series 2.7 v reset output sink current vs. input voltage figure 19. ncp304h/5l series 4.5 v reset output sink current vs. input voltage figure 20. ncp304h/5h series 2.7 v reset output sink current vs. input voltage t a = 25 c t a = 25 c
ncp304, ncp305 http://onsemi.com 14 10 8.0 0 0 2.0 4.0 6.0 8.0 10 v in , input voltage (v) 2.0 4.0 6.0 12 v out = v in -2.1 v v in -1.5 v v in -1.0 v v in -0.5 v t a = 25 c i out , output source current (ma) 0 2.0 2.0 3.0 2.5 1.5 1.0 v in , input voltage (v) i out , output source current (ma) 1.0 0 0.5 4.0 3.0 t a = -30 c t a = 25 c t a = 85 c 10 8.0 2.0 0 0 2.0 4.0 6.0 8.0 10 v in , input voltage (v) 4.0 6.0 12 v out = v in -2.1 v v in -1.5 v v in -1.0 v v in -0.5 v t a = 25 c 10 8.0 0 0 2.0 4.0 6.0 8.0 10 v in , input voltage (v) 2.0 4.0 6.0 12 v out = v in -2.1 v v in -1.5 v v in -1.0 v v in -0.5 v t a = 25 c i out , output source current (ma) i out , output source current (ma) figure 21. ncp304h series 0.9 v reset output source current vs. input voltage figure 22. ncp304h series 2.7 v reset output source current vs. input voltage figure 23. ncp304h series 4.5 v reset output source current vs. input voltage figure 24. ncp304h series 2.7 v reset output source current vs. input voltage
ncp304, ncp305 http://onsemi.com 15 operating description the ncp304 and ncp305 series devices are second generation ultra-low current voltage detectors. figures 25 and 26 show a timing diagram and a typical application. initially consider that input voltage v in is at a nominal level and it is greater than the voltage detector upper threshold (v det+ ), and the reset output (pin 1) will be in the high state for active low devices, or in the low state for active high devices. if there is a power interruption and v in becomes significantly deficient, it will fall below the lower detector threshold (v det- ). this sequence of events causes the reset output to be in the low state for active low devices, or in the high state for active high devices. after completion of the power interruption, v in will again return to its nominal level and become greater than the v det+ . the voltage detector has built-in hysteresis to prevent erratic reset operation as the comparator threshold is crossed. although these device series are specifically designed for use as reset controllers in portable microprocessor based systems, they offer a cost-effective solution in numerous applications where precise voltage monitoring is required. figure 26 through figure 32 shows various application examples. figure 25. timing waveforms v in v det + v det- input voltage, pin 2 v in 0 v reset output (active low), pin 1 reset output (active high), pin 1 v in 0 v v det + v det- v det + v det-
ncp304, ncp305 http://onsemi.com 16 application circuit information figure 26. microprocessor reset circuit 2 input 1 reset output gnd ncp304 lsq27t1 figure 27. battery charge indicator 2 input 1 reset output gnd gnd v dd reset v dd ncp304 series 4 4 microprocessor * required for ncp305 v in < 2.7 on v in > 2.835 on to additional circuitry * 2.85 v 2.70 v low state output if either power supply is below the respective undervoltage de\ tector threshold but greater than 1.0 v. 2 1 ncp305 lsq45t1 figure 28. dual power supply undervoltage supervision 4 v supply 2 1 ncp305 lsq30t1 4 3.3 v 5.0 v gnd input reset output gnd input reset output
ncp304, ncp305 http://onsemi.com 17 figure 29. microprocessor reset circuit with additional hysteresis 2 1 ncp301 lsn27t1 4 v dd gnd reset output input r h r l ncp301 lsn27t1 ncp305 lsq27t1 gnd reset v dd microprocessor comparator hysteresis can be increased with the addition of resistor r h . the hysteresis equations have been simplified and do not account for the change of input current i in as v in crosses the comparator threshold. the internal resistance, r in is simply calculated using i in = 0.26 a at 2.6 v. v in decreasing: v th r h r in 1 v det v in increasing: v th r h r in r l 1 v det v hys v hys = v in increasing - v in decreasing test data v th decreasing (mv) v th increasing (mv) v hys (mv) r h ( ) r l (k ) 2.70 2.70 2.70 2.70 2.70 2.70 2.70 2.70 2.70 2.70 2.84 2.87 2.88 2.91 2.90 2.94 2.98 2.70 3.04 3.15 0.135 0.17 0.19 0.21 0.20 0.24 0.28 0.27 0.34 0.35 0 100 100 100 220 220 220 470 470 470 figure 30. simple clock oscillator ncp301 lsn27t1 gnd reset output input 82 k ncp301 lsn27t1 ncp302 hsq27t1 c 5.0 v 100 k c ( f) f osc (khz) i q ( a) 0.01 2590 21.77 0.1 490 21.97 1.0 52 22.07 test data 2 4 1
ncp304, ncp305 http://onsemi.com 18 figure 31. microcontroller systems load sensing ncp301 lsn27t1 50 k ncp301 lsn27t1 ncp305 lsq09t1 v supply load r sense input 2 4 gnd 1 reset output microcontroller gnd v dd if: i load v det- /r sense i load (v det - +v hys )/r sense then: reset output = 0 v reset output = v dd this circuit monitors the current at the load. as current flows through the load, a voltage drop with respect to ground appears across r sense where v sense = i load * r sense. the following conditions apply: figure 32. led bar graph ncp301 lsn27t1 2 ncp301 lsn27t1 ncp305 lsq45t1 4 1 v supply ncp301 lsn27t1 2 ncp301 lsn27t1 ncp305 lsq27t1 4 1 ncp301 lsn27t1 2 ncp301 lsn27t1 ncp305 lsq18t1 4 1 input gnd reset output input gnd reset output input gnd reset output v in = 1.0 v to 10 v a simple voltage monitor can be constructed by connecting several voltage detectors as shown above. each led will sequentially turn on when the respective voltage detector threshold (v det- +v hys ) is exceeded. note that detector thresholds (v det- ) that range from 0.9 v to 4.9 v in 100 mv steps can be manufactured.
ncp304, ncp305 http://onsemi.com 19 ordering information device threshold voltage output type reset marking package shipping ? ncp304lsq09t1 0.9 cmos active low shg sc-82ab 3000 / tape & reel ncp304lsq09t1g 0.9 shg sc-82ab (pb-free) ncp304lsq18t1 1.8 sgx sc-82ab ncp304lsq18t1g 1.8 sgx sc-82ab (pb-free) ncp304lsq20t1 2.0 sgv sc-82ab ncp304lsq20t1g 2.0 sgv sc-82ab (pb-free) ncp304lsq23t1 2.3 sgr sc-82ab ncp304lsq23t1g 2.3 sgr sc-82ab (pb-free) ncp304lsq25t1 2.5 sgp sc-82ab ncp304lsq25t1g 2.5 sgp sc-82ab (pb-free) ncp304lsq27t1 2.7 sgn sc-82ab ncp304lsq27t1g 2.7 sgn sc-82ab (pb-free) ncp304lsq29t1 2.9 sgk sc-82ab ncp304lsq29t1g 2.9 sgk sc-82ab (pb-free) ncp304lsq30t1 3.0 sgj sc-82ab ncp304lsq30t1g 3.0 sgj sc-82ab (pb-free) ncp304lsq33t1 3.3 sgg sc-82ab ncp304lsq33t1g 3.3 sgg sc-82ab (pb-free) ncp304lsq37t1 3.7 sgb sc-82ab ncp304lsq37t1g 3.7 sgb sc-82ab (pb-free) ncp304lsq38t1 3.8 sga sc-82ab ncp304lsq38t1g 3.8 sga sc-82ab (pb-free) ncp304lsq40t1 4.0 sfy sc-82ab ncp304lsq40t1g 4.0 sfy sc-82ab (pb-free) ncp304lsq42t1 4.2 sfu sc-82ab ncp304lsq42t1g 4.2 sfu sc-82ab (pb-free) ncp304lsq43t1 4.3 sfv sc-82ab ncp304lsq43t1g 4.3 sfv sc-82ab (pb-free) ncp304lsq45t1 4.5 sfs sc-82ab ncp304lsq45t1g 4.5 sfs sc-82ab (pb-free) note: the ordering information lists st andard undervoltage thresholds with active low outputs. additional active low threshold devices, ranging from 0.9 v to 4.9 v in 100 mv increments and ncp304 active high output devices, ranging from 0.9 v to 4.9 v in 100 mv increment s can be manufactured. contact your on semiconductor representative for availability. the electrical characteristics of these add itional devices are shown in tables 1 and 2. ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging spe\ cifications brochure, brd8011/d.
ncp304, ncp305 http://onsemi.com 20 ordering information device shipping ? package marking reset output type threshold voltage ncp304lsq46t1 4.6 cmos active low sfr sc-82ab (pb-free) 3000 / tape & reel NCP304LSQ46T1G 4.6 sfr sc-82ab (pb-free) ncp304lsq47t1 4.7 sfq sc-82ab ncp304lsq47t1g 4.7 sfq sc-82ab (pb-free) ncp304hsq09t1 0.9 cmos active high snq sc-82ab 3000 / tape & reel ncp304hsq09t1g 0.9 snq sc-82ab (pb-free) ncp304hsq18t1 1.8 snz sc-82ab ncp304hsq18t1g 1.8 snz sc-82ab (pb-free) ncp304hsq20t1 2.0 sob sc-82ab ncp304hsq20t1g 2.0 sob sc-82ab (pb-free) ncp304hsq22t1 2.2 sod sc-82ab ncp304hsq22t1g 2.2 sod sc-82ab (pb-free) ncp304hsq27t1 2.7 soi sc-82ab ncp304hsq27t1g 2.7 soi sc-82ab (pb-free) ncp304hsq29t1 2.9 sok sc-82ab ncp304hsq29t1g 2.9 sok sc-82ab (pb-free) ncp304hsq30t1 3.0 sol sc-82ab ncp304hsq30t1g 3.0 sol sc-82ab (pb-free) ncp304hsq45t1 4.5 spa sc-82ab ncp304hsq45t1g 4.5 spa sc-82ab (pb-free) ncp304hsq47t1 4.7 spc sc-82ab ncp304hsq47t1g 4.7 spc sc-82ab (pb-free) ncp305lsq09t1 0.9 open drain active low siz sc-82ab 3000 / tape & reel ncp305lsq09t1g 0.9 siz sc-82ab (pb-free) ncp305lsq11t1 1.1 six sc-82ab ncp305lsq11t1g 1.1 six sc-82ab (pb-free) ncp305lsq15t1 1.5 sis sc-82ab ncp305lsq15t1g 1.5 sis sc-82ab (pb-free) note: the ordering information lists st andard undervoltage thresholds with active low outputs. additional active low threshold devices, ranging from 0.9 v to 4.9 v in 100 mv increments and ncp304 active high output devices, ranging from 0.9 v to 4.9 v in 100 mv increment s can be manufactured. contact your on semiconductor representative for availability. the electrical characteristics of these add itional devices are shown in tables 1 and 2. ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging spe\ cifications brochure, brd8011/d.
ncp304, ncp305 http://onsemi.com 21 ordering information device threshold voltage output type reset marking package shipping ? ncp305lsq16t1 1.6 open drain active low sir sc-82ab 3000 / tape & reel ncp305lsq16t1g 1.6 sir sc-82ab (pb-free) ncp305lsq17t1 1.7 siq sc-82ab ncp305lsq17t1g 1.7 siq sc-82ab (pb-free) ncp305lsq18t1 1.8 sip sc-82ab ncp305lsq18t1g 1.8 sip sc-82ab (pb-free) ncp305lsq20t1 2.0 sin sc-82ab ncp305lsq20t1g 2.0 sin sc-82ab (pb-free) ncp305lsq22t1 2.2 sik sc-82ab ncp305lsq22t1g 2.2 sik sc-82ab (pb-free) ncp305lsq23t1 2.3 sij sc-82ab ncp305lsq23t1g 2.3 sij sc-82ab (pb-free) ncp305lsq24t1 2.4 sii sc-82ab ncp305lsq24t1g 2.4 sii sc-82ab (pb-free) ncp305lsq25t1 2.5 sih sc-82ab ncp305lsq25t1g 2.5 sih sc-82ab (pb-free) ncp305lsq27t1 2.7 sif sc-82ab ncp305lsq27t1g 2.7 sif sc-82ab (pb-free) ncp305lsq28t1 2.8 sie sc-82ab ncp305lsq28t1g 2.8 sie sc-82ab (pb-free) ncp305lsq29t1 2.9 sid sc-82ab ncp305lsq29t1g 2.9 sid sc-82ab (pb-free) ncp305lsq30t1 3.0 sic sc-82ab ncp305lsq30t1g 3.0 sic sc-82ab (pb-free) ncp305lsq30t3 3.0 open drain active low sic sc-82ab 10,000 / tape & reel ncp305lsq30t3g 3.0 sic sc-82ab (pb-free) ncp305lsq31t1 3.1 open drain active low sib sc-82ab 3000 / tape & reel ncp305lsq31t1g 3.1 sib sc-82ab (pb-free) ncp305lsq32t1 3.2 sia sc-82ab ncp305lsq32t1g 3.2 sia sc-82ab (pb-free) note: the ordering information lists st andard undervoltage thresholds with active low outputs. additional active low threshold devices, ranging from 0.9 v to 4.9 v in 100 mv increments and ncp304 active high output devices, ranging from 0.9 v to 4.9 v in 100 mv increment s can be manufactured. contact your on semiconductor representative for availability. the electrical characteristics of these add itional devices are shown in tables 1 and 2. ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging spe\ cifications brochure, brd8011/d.
ncp304, ncp305 http://onsemi.com 22 ordering information device shipping ? package marking reset output type threshold voltage ncp305lsq33t1 3.3 open drain active low shz sc-82ab 3000 / tape & reel ncp305lsq33t1g 3.3 shz sc-82ab (pb-free) ncp305lsq34t1 3.4 shy sc-82ab ncp305lsq34t1g 3.4 shy sc-82ab (pb-free) ncp305lsq35t1 3.5 shx sc-82ab ncp305lsq35t1g 3.5 shx sc-82ab (pb-free) ncp305lsq36t1 3.6 shu sc-82ab ncp305lsq36t1g 3.6 shu sc-82ab (pb-free) ncp305lsq37t1 3.7 shv sc-82ab ncp305lsq37t1g 3.7 shv sc-82ab (pb-free) ncp305lsq40t1 4.0 shr sc-82ab ncp305lsq40t1g 4.0 shr sc-82ab (pb-free) ncp305lsq44t1 4.4 shn sc-82ab ncp305lsq44t1g 4.4 shn sc-82ab (pb-free) ncp305lsq45t1 4.5 shl sc-82ab ncp305lsq45t1g 4.5 shl sc-82ab (pb-free) ncp305lsq47t1 4.7 shj sc-82ab ncp305lsq47t1g 4.7 shj sc-82ab (pb-free) ncp305lsq49t1 4.9 shh sc-82ab ncp305lsq49t1g 4.9 shh sc-82ab (pb-free) note: the ordering information lists st andard undervoltage thresholds with active low outputs. additional active low threshold devices, ranging from 0.9 v to 4.9 v in 100 mv increments and ncp304 active high output devices, ranging from 0.9 v to 4.9 v in 100 mv increment s can be manufactured. contact your on semiconductor representative for availability. the electrical characteristics of these add itional devices are shown in tables 1 and 2. ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging spe\ cifications brochure, brd8011/d.
ncp304, ncp305 http://onsemi.com 23 package dimensions sc-82ab sq suffix case 419c-02 issue e notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. 419c-01 obsolete. new standard is 419c-02. 4. dimensions a and b do not include mold flash, protrusions, or gate burrs. 12 3 a g s n j k 4 d 3 pl b f l c h 0.05 (0.002) dim min max min max inches millimeters a 1.8 2.2 0.071 0.087 b 1.15 1.35 0.045 0.053 c 0.8 1.1 0.031 0.043 d 0.2 0.4 0.008 0.016 f 0.3 0.5 0.012 0.020 g 1.1 1.5 0.043 0.059 h 0.0 0.1 0.000 0.004 j 0.10 0.26 0.004 0.010 k 0.1 --- 0.004 --- l 0.05 bsc 0.002 bsc n 0.2 ref 0.008 ref s 1.8 2.4 0.07 0.09 *for additional information on our pb-free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. soldering footprint* 1.30 0.0512 mm inches scale 10:1 0.65 0.026 1.90 0.075 0.90 0.035 0.70 0.028 0.95 0.037 on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to mak e changes without further notice to any products herein. scillc makes no warranty , representation or guarantee regarding the suitability of its products for an y particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including wi thout limitation special, consequential or incidental damages. typical parameters which may be provided in scillc data sheets and/or specifications can and do vary in different application s and actual performance may vary over time. all operating parameters, including typicals must be validated for each customer application by customer's technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its of ficers, employees, subsidiaries, af filiates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. publication ordering information n. american technical support : 800-282-9855 toll free ?usa/canada europe, middle east and africa technical support: ?phone: 421 33 790 2910 japan customer focus center ?phone: 81-3-5773-3850 ncp304/d literature fulfillment : ?literature distribution center for on semiconductor ?p.o. box 5163, denver, colorado 80217 usa ? phone : 303-675-2175 or 800-344-3860 toll free usa/canada ? fax : 303-675-2176 or 800-344-3867 toll free usa/canada ? email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your local sales representative

▲Up To Search▲

Price & Availability of NCP304LSQ46T1G

	To Download NCP304LSQ46T1G Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .